Hardware: Linksys E2500 running AdvancedTomato and Linksys E1000 v1 running DD-WRT Firmware: dd-wrt.v24-21061_NEWD-2_K2.6_mini_e1000v1.bin works as expected Firmware: dd-wrt.v24-41303_NEWD-2_K2.6_mini_e1000v1.bin shows issue Environment: E2500 is set up as AP+WDS and has the MAC address for the E1000 configured.
List of Tomato firmware supported devices - DeviWiki (ex DD-WRT TomatoUSB OpenWrt Linksys E1000 v2.0 FCC ID: Q87-E1000V2: wireless router bgn CyberTAN CoO: 20px: Broadcom BCM5357B0 @ 300 MHz: 4 MiB. 4,194,304 B 32,768 Kib 4,096 KiB 32 Mib 0.00391 GiB . 32 MiB. 33,554,432 B 262,144 Kib 32,768 KiB 256 Mib 0.0313 GiB . Broadcom BCM5357B0 2x2:2, bgn: BCM5357B0: 100M 4 LAN 1 WAN OpenWrt Project: Linksys WRT3200ACM Image Name: Linksys WRT3200 Router Created: 2018-01-11 5:42:22 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4640515 Bytes = 4.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum Cisco Linksys e1000 Bridge Solutions | Experts Exchange in addition to replacing the linksys firmware with dd-wrt, I will still need to run the cable between the AT&T wireless router and the cisco Linksys e1000 wireless router ? OR the dd-wrt firmware will enable the cisco linksys e1000 to bridge with the AT&T router without the need of running a cable between them ?
How to Install DD-WRT on Your Router
Linksys E2000 - DD-WRT Wiki DD-WRT Build Info Brainslayer added E2000 support in 14929, and builds are found in the broadcom_K26 folder for each build. Build 25974 works well but later k2.6 builds have VAP issues. How to Install DD-WRT on Your Router May 06, 2020
DD-WRT Forum :: View topic - Linksys E1000 v2.1
Mar 28, 2011 Linksys E1000 VPN Router Review - vpnsp.com Linksys E1000 router details: The Linksys E2000 is a wireless-N 300 Mbps router. DD-WRT firmware installed; Gigabit 4-port switch. Cisco Linksys E1000 custom firmware options: Flashed with DD-WRT firmware; Supported VPN protocols: OpenVPN, PPTP; Supported operating systems / mobile devices: Windows, Mac OS/X, Linux; iOS (iPad, iPhone, iPod Reference the Linksys E1000 wiki for the general procedure and information NOTE: use the mini_e1000v2.bin trailed build from the broadcom_K26 folder. Minimum build for v2.0 is 16758 and for v2.1 is 16698; Do not use older mini_e1000.bin v1 builds which are prior to v2 support With a wired connection, log into the Linksys Web Interface Firmware Upgrade page. Do a reset using the stock web interface. Wait a minute. Flash the initial flash firmware: dd-wrt.v24-19519_NEWD-2_K2.6_mini-e1200v2.bin Wait 2 minutes for the router to flash and reboot itself. Wait about another 2 minutes until it finishes booting.